Geotechnical·MCQ explained

If the velocity of flow of water through the soil is 0.01 cm/s and the piezometer readings at the end points A and B of soil sample are 10 cm and 5 cm, respectively. The distance between the points A and B is 20 cm. Find the coefficient of permeability of the soil sample.

Try it first: pick an option, then read the explanation.

Correct answer: B. 0.04 cm/s

Detailed Explanation

Darcy's law is the foundational relationship in this entire topic: the velocity of flow through a saturated soil is directly proportional to the hydraulic gradient driving it, with the coefficient of permeability (K) as the proportionality constant.

Given: velocity of flow v = 0.01 cm/s; piezometric head at A, hA = 10 cm; piezometric head at B, hB = 5 cm; distance L = 20 cm.

Step 1 — Hydraulic gradient: i = (hA − hB)/L = (10 − 5)/20 = 5/20 = 0.25

Step 2 — Coefficient of permeability: from v = K·i, K = v/i = 0.01/0.25 = 0.04 cm/s

Why "0.04 cm/s" Is Correct

Substituting the given velocity and the computed hydraulic gradient into Darcy's law (v = K·i, rearranged as K = v/i) gives K = 0.01/0.25 = 0.04 cm/s.

CONSTANT HEAD / DARCY SET-UPSoil SampleAhABhBLength L, Area Aflow direction →

Piezometers at points A and B measure the piezometric head at each end of the sample. Hydraulic gradient i = (hA − hB)/L, and Darcy's law gives v = K·i.

Why the Other Options Are Wrong

  • 4 cm/s: off by a factor of 100 — likely from dividing i by v instead of v by i, or a decimal-point slip.
  • 0.25 cm/s: this is the hydraulic gradient (i) itself, not the coefficient of permeability — a common mix-up between the two quantities.
  • 0.025 cm/s: close to the correct value but not matching the arithmetic — likely from a small computational slip in the final division.

Key Point

Always compute the hydraulic gradient i FIRST (head difference over distance), then divide velocity by i to get K — never divide the two raw head values directly.

Key Concepts for Students

  • Hydraulic gradient i is dimensionless (head difference and distance are both lengths, so their ratio has no units) — only v and K carry units of velocity.
  • This exact v = K·i relationship, just rearranged, is the basis of every basic Darcy's law numeric question in this topic.
  • Piezometric head, not just elevation, is what matters — piezometers directly measure this head at each point.
  • See the Going Deeper section for Darcy's law's full derivation, assumptions, and validity limits.

Going Deeper: Darcy's Law: Full Derivation and Assumptions

Darcy's law states that, for laminar flow through a saturated, homogeneous soil, the discharge velocity is directly proportional to the hydraulic gradient: v ∝ i, or v = K·i, where K is the coefficient of permeability.

Multiplying both sides by the cross-sectional area A of the soil sample gives the rate of discharge: q = K·i·A — this form is used directly in field-well problems (Q20, Q21) and flow-net discharge calculations (Q31).

AssumptionWhy It Matters
Soil is fully saturatedDarcy's law describes flow through water-filled voids; partial saturation changes the flow behaviour
Flow is laminar (Reynolds number < 1)At higher velocities, flow becomes turbulent and v is no longer simply proportional to i (see Q13)
Soil is homogeneous and isotropicPermeability is assumed constant in all directions and throughout the sample

Darcy's law is valid up to a particle size of about 0.5 mm (see Q8) — beyond that (very coarse gravel), flow velocities become high enough that turbulence sets in and the simple linear v-i relationship breaks down.