Home/MCQ Practice/Surveying MCQs/Land Surveying

Surveying·MCQ practice

MCQs on Land Surveying – Set 2

15 questions. Tap an option to check it instantly, then read the solution.

Question 1Medium
What are the errors that cannot be eliminated in surveying?
Full explanation

Answer: D. Random errors

Random errors, also known as accidental errors, are unpredictable variations in measurements that occur without a recognizable pattern. While they can be minimized by repeating measurements and applying statistical methods, they cannot be completely eliminated. Systematic errors (instrumental, personal, natural causes) can typically be identified and corrected.

Question 2Easy
What is the common scale adopted in the form of a representative fraction for a forest map?
Full explanation

Answer: C. 1/25000

The 1:25,000 scale is a standard topographical map scale used for various purposes, including forestry. It provides a good balance of detail and area coverage, making it suitable for managing and planning forest areas.

Question 3Hard
A line of 5 m on the original map is shrunk to 4.6 m. Calculate the shrunk scale if the original scale of the map was 1 cm = 80 m.
Full explanation

Answer: C. 1 cm = 86.95 m

First, calculate the Shrinkage Factor (SF).
SF = Shrunk Length / Original Length = 4.6 m / 5 m = 0.92.
The shrunk scale is found by dividing the original scale's ground distance by the SF.
New ground distance = 80 m / 0.92 = 86.9565 m.
So, the new scale is 1 cm = 86.95 m.

Question 4Medium
10 divisions of a Vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the least count of the Vernier scale?
Full explanation

Answer: B. 0.01 mm

This describes a retrograde Vernier scale. The value of one main scale division (s) is 0.1 mm. The value of one Vernier scale division (v) is (11/10) * 0.1 mm = 0.11 mm. The least count (LC) is the difference between one Vernier division and one main scale division: LC = v - s = 0.11 mm - 0.1 mm = 0.01 mm.

Question 5Easy
With an increase in the denominator of the representative fraction, the scale of the map will:
Full explanation

Answer: A. Decrease

The representative fraction (RF) represents the ratio of map distance to ground distance. A larger denominator (e.g., 1/50,000) means 1 unit on the map represents a larger distance on the ground compared to a smaller denominator (e.g., 1/5,000). This results in a smaller scale map, which covers a larger area with less detail. Therefore, as the denominator increases, the scale decreases.

Question 6Hard
A line of 5 m on the original map is shrunk to 4.6 m. Calculate the shrunk scale if the original scale of the map was 1 cm = 80 m.
Full explanation

Answer: C. 1 cm = 86.95 m

First, calculate the Shrinkage Factor (SF).
SF = Shrunk Length / Original Length = 4.6 m / 5 m = 0.92.
The shrunk scale is found by dividing the original scale's ground distance by the SF.
New ground distance = 80 m / 0.92 = 86.9565 m.
So, the new scale is 1 cm = 86.95 m.

Question 7Medium
Plumb bob lines at two different places in geodetic surveying will _____.
Full explanation

Answer: B. Intersect at the center of the Earth

In geodetic surveying, the curvature of the Earth is considered. Plumb lines indicate the direction of gravity, which points towards the Earth's center of mass. Therefore, lines of gravity from two different points will converge and intersect at the center of the Earth. In plane surveying, they are assumed to be parallel.

Question 8Hard
In geodetic surveying, the sum of angles (in degrees) of a spherical triangle should not be greater than _____.
Full explanation

Answer: D. 540

For a triangle on a spherical surface, the sum of the interior angles is always greater than 180° and less than 540°. This is a key difference from a plane triangle, where the sum is exactly 180°.

Question 9Medium
Calculate the number of divisions of the main scale that is equal to the 8 divisions of the extended vernier.
Full explanation

Answer: C. 15

In an extended vernier, 'n' divisions of the vernier scale are equal to (2n - 1) divisions of the main scale. In this case, n = 8. Therefore, the number of main scale divisions is (2 * 8) - 1 = 16 - 1 = 15.

Question 10Hard
An area of a field is 250 square centimetres from a shrunk map having a shrunk factor of 0.9. Calculate the original area (square metres) on the field, if the original scale of the map is 1 cm = 50 m.
Full explanation

Answer: D. 771450

First, find the original area on the map before it shrunk. The shrunk area factor is (Shrinkage Factor)² = (0.9)² = 0.81.
Original Map Area = Shrunk Map Area / Shrunk Area Factor = 250 cm² / 0.81 ≈ 308.64 cm².
Next, use the original scale to find the field area. The area scale is (50 m/cm)² = 2500 m²/cm².
Original Field Area = Original Map Area × Area Scale Factor = 308.64 cm² × 2500 m²/cm² ≈ 771,605 m². The closest answer is 771,450.

Question 11Easy
Which one of the following surveys is used to define property lines?
Full explanation

Answer: B. Cadastral survey

Cadastral surveys are specifically conducted to determine and define land ownership and property boundaries for legal purposes, including for taxation and property deeds.

Question 12Easy
The vernier that is calibrated in the direction opposite to the main scale is called ........
Full explanation

Answer: D. retrograde vernier

A retrograde vernier has its divisions marked in the opposite direction to the main scale. On this type of vernier, the divisions are slightly larger than the main scale divisions.

Question 13Medium
What is the representative fraction for a scale of 10 cm = 20 km ?
Full explanation

Answer: D. 1 : 200,000

To find the Representative Fraction (RF), both units must be the same.
First, simplify the given scale: 10 cm = 20 km is the same as 1 cm = 2 km.
Now, convert km to cm: 1 km = 100,000 cm, so 2 km = 200,000 cm.
The scale is 1 cm on the map equals 200,000 cm on the ground. Therefore, the RF is 1 : 200,000.

Question 14Easy
The vernier scale in which 10 divisions of the vernier scale is equal to 9 divisions of the main scale is called _______.
Full explanation

Answer: A. direct vernier

This is the definition of a direct vernier. The divisions on the vernier scale are slightly smaller than the divisions on the main scale, and it is read in the same direction as the main scale.

Question 15Medium
The maximum error (mm) on the drawing should not be greater than ______
Full explanation

Answer: C. 0.25

This is a standard convention in drafting and cartography. It is based on the limit of human vision, where a deviation smaller than 0.25 mm is generally not discernible to the naked eye. This value is also known as the limit of plotting accuracy.